Hello,
I managed to perform the masterpiece of breaking a frame screw when installing new exterior doors. A moment of inattention caused the inner screw to become "rounded" off, and now it's impossible to adjust the frame screw. Does anyone have any good tips on how to remove a damaged frame screw? Saw off the screw itself and drill out the sleeve, or saw off and cover the sleeve and drill a new hole in the frame? All tips and ideas are warmly welcomed!
I managed to perform the masterpiece of breaking a frame screw when installing new exterior doors. A moment of inattention caused the inner screw to become "rounded" off, and now it's impossible to adjust the frame screw. Does anyone have any good tips on how to remove a damaged frame screw? Saw off the screw itself and drill out the sleeve, or saw off and cover the sleeve and drill a new hole in the frame? All tips and ideas are warmly welcomed!
Cut the screw between the frame and the stud as close to the frame as you can, then you can unscrew the sleeve. Then, take a polygrip and unscrew the part of the screw that is stuck in the stud. I managed the same with a storage room door.
Member
· Korpilombolo
· 3 723 posts
A couple of frame screws became rounded due to the lousy yet expensive tools and poor precision of the screws before I pre-drilled the remaining screw holes in the wall. The zinc sleeve can be difficult to remove from the old hole without damaging it. The easiest way is to drill a new 14 mm hole and insert a new frame screw next to the old one that has been cut.
I bought Serva's frame screws and stripped 3 out of 6. And this with Serva's own bits. Total crap. Bring out the angle grinder and then hammer in nails instead.
Biltema's door frame screw I almost messed up before I also pre-drilled. What you MUST check is that the hole for the zinc sleeve is deep enough, which it was not in my sauna door.
Used Biltema's own tools/frame screws and I think the precision on it is good. Used a ratchet and it went quite heavy.
Used Biltema's own tools/frame screws and I think the precision on it is good. Used a ratchet and it went quite heavy.
The whole thing ended with me having to saw off the frame screws that had rounded off and got stuck, and after a lot of hassle, I managed to get them out of the frame. Then I purchased adjufix, and the whole thing was fixed in 1 hour. I must say that adjufix is an incredibly more stable construction than the regular frame screws. They are somewhat more expensive, but they are worth it every day of the week.
Fredrik
Fredrik
As a tip; always pre-drill and also drill a through-hole for the sleeve to make adjustments even easier. There is a special drill bit for frame screws that drills for both the sleeve and the screw in one process, but for single doors or windows, it might be a bit of overkill, though I must admit it's super convenient. Then I drive everything with the screwdriver, but you need to proceed carefully to avoid stripping the screw head.
First and foremost, if you are going to use traditional frame screws (14 mm), drill through the frame, as it's usually only halfway drilled.
Buy a proper frame key, (T model, and also buy a socket, that's the one used to drive in the entire screw).
Put the socket in a strong screwdriver or drill, and then drive them in so far that you see the rounding on the 14 mm screw.
Then use the T-key to adjust. I promise it's money well spent, because you can also adjust the frames years later if needed.
Use well-known brands like Essve and such...
Buy a proper frame key, (T model, and also buy a socket, that's the one used to drive in the entire screw).
Put the socket in a strong screwdriver or drill, and then drive them in so far that you see the rounding on the 14 mm screw.
Then use the T-key to adjust. I promise it's money well spent, because you can also adjust the frames years later if needed.
Use well-known brands like Essve and such...