Need to remove the current window whose frame has started to rot due to moisture in the basement. The basement only has a hydropress and filter and doesn't serve any other function right now. I was thinking of temporarily replacing the window with some type of cover plate since I don't have time or want to spend money on a window right now. I want something that keeps it sealed and maybe even insulate it a bit, even if it's a "cold basement" I don't want the water to freeze there in the winter (I have a frost guard).

I have considered removing the window and frame entirely. Then screw a couple of pressure-treated beams into the opening (in the concrete), or maybe even four so it forms a frame. I was thinking of placing roofing felt (or something else?) between the beams and the concrete because I've heard you shouldn't have wood directly against concrete. In this frame (or if there are just two horizontal or vertical beams, I planned to attach a fiber cement board of appropriate size (a bit of overlap on the outside of the concrete, maybe 10-15 cm all around?) on the outside with screws in the wooden frame. Maybe I can also put some type of insulation, e.g. foam plastic, in the wooden frame and then also screw a board on the inside of the frame, some type of plywood perhaps? Do you need any kind of sealing strip or sealant between the fiber cement board and the outside of the concrete wall?

Does this sound like a good temporary solution? By temporary, I mean it should ideally last for a few years at least, preferably more. Other suggestions? It should be as simple and cheap as possible, but still last a few years.
 
  • Like
Engladgubbe
  • Laddar…
P
The fastest but still relatively sustainable solution would be as you thought, with a layer of roofing felt in the opening and a frame around the outer edge. Depending on how damp it is, it might be best to use ground insulation in the hole and then a wooden board on each side, or perhaps a fiber cement board.

Otherwise, a new window, perhaps one that doesn't rot, made of plastic/composite material, would be a good solution that doesn't look as abandoned as a ghetto style...

Or if a window is not desired at all, the most elegant solution would be to brick up the hole and plaster both the inside and outside, or match the appearance of the rest of the basement wall... if you cheat with lecablock, then it's a question of whether it is almost both the cheapest and best solution. Compared to a board for the hole, it doesn't increase the risk of unwanted visitors. The material costs just a few coins.
 
Or buy some glass blocks.
It will be sealed, looks like a window and not a broken window pane, and you still get some light into the room.
 
  • Like
fribygg and 3 others
  • Laddar…
Ok, I've looked around a bit and found a fairly priced window for about 1800:-. It feels like it won't be much more expensive than making a proper temporary solution. So, it will probably be a window instead. Then comes the question of how to fit a new window where an old one was, in concrete? There will likely be holes that "almost" match the frame sleeve holes in the new window. The idea with frame sleeves/screws is to easily adjust the window to be level and properly centered, and then directly drill and screw it in place. This doesn't really work when there are already existing holes in the concrete. Is there any good filler you can put in the holes and then drill new holes quite close to the old ones?
 
I irrbloss said:
Ok I have looked around a bit and found a fairly priced window for about 1800:-. It feels like it won't be much more expensive than making a proper temporary solution. So it will probably be a window instead after all. Then the question arises, how do you fit a new window where an old one has been, in concrete? There are likely holes that "almost" align with the frame sleeve holes in the new window. The idea with frame sleeves/screws is to easily adjust the window level and centered properly, then drill and screw into place. This doesn't work entirely when there are already existing holes in the concrete. Is there no good filling you can press into the holes and then drill new ones quite close to the old ones?
There are usually plugs included to cover the holes. Then you can drill new holes (14 mm) almost wherever you want.
 
T Thomas_Blekinge said:
They usually come with plugs to cover the holes. Then you can drill new holes (14 mm) almost anywhere you like.
Since it's a basement window, unfortunately, it's not very tall, so there's not much leeway there. I remember that you preferably shouldn't drill holes closer than about 10 cm from an old hole if you want to avoid cracks or poor anchorage. Now, I don't know exactly how big the window is, but from memory, I would say somewhere around 50 cm tall, of which the inside of the frame would then maybe be around 35-40 cm for two holes that shouldn't be too close to the old holes.
 
Click here to reply
Vi vill skicka notiser för ämnen du bevakar och händelser som berör dig.