What's the fitting called?

[p3p3]

Hi,

I need to attach reinforcement mesh within a large number of frames, of varying dimensions. I have seen this done with a similar fitting as in the picture. This one was made by drilling a "pipe holder" from Bauhaus. Since I need about 100, it would be much more convenient to buy them ready-made.

Does anyone know if they exist and what they are called?

The center hole needs to be about 7mm as the reinforcement mesh is 6mm.

Thanks!

 

[Jensa86]

Pipe clamp?

 

[C.Lundin]

Think it might be difficult to find. Never seen and don't know what they would be used for.
Is it a träram? Drill holes in the frame at the right cc and "thread" the frame onto the reinforcement?

 

[tttomten]

Seems like it's a pipe clamp with a stop screw. But 7 mm seems large... the ones I've seen are around 3-4 mm.
There are large ones for 32/50/76 mm pipes, and they probably have a 5-6 mm stop screw. But using those seems expensive. See for example:
https://www.svebry.se/en/product/rorklammer-50mm

 

[p3p3]

I believe it might be difficult to get hold of. Never seen and don't know what they would be used for. Is it a wooden frame? Drill holes in the frame at the correct cc and "thread" the frame onto the reinforcement?

Hope to avoid that! It will be time-consuming to fit in every direction. This solves the whole problem.

 

[p3p3]

Seems like a pipe clamp with a set screw. But 7 mm, seems big...the ones I've seen are around 3-4 mm.
There are large ones for 32/50/76 mm pipes and they probably have 5-6 mm set screws. But using such seems expensive. See e.g.
[link]

Definitely expensive! The one I've used now for testing costs 10:-. But thanks for searching and the tips!

 

[Pappa1986]

Hello,

I am going to attach a reinforcement mesh within a large number of frames of varying dimensions. I have seen it done with a similar fitting as in the picture. This one was made by drilling a "pipe holder" from Bauhaus. Since I need about 100, it would be much more convenient to buy ready-made.

Anyone know if it exists and what it's called?

The center hole needs to be about 7mm since the reinforcement mesh is 6mm.

Thanks!

Could a mounting band work?

 

[KnockOnWood]

Could it work with a montage band?
[image]

Smart!
Then you just cut, fold, press together with pliers and screw.
And it's enough with one screw in each if you fold it double:

 

[C.Lundin]

Hope to avoid that! It gets time-consuming to fit on all fronts. This kind of solves the whole problem.

All irons are on the same cc, measuring and drilling everything will probably take you 4-5 minutes, I would think. You have a much clearer picture of what you want, but it was just a tip!

 

[p3p3]

Smart!
Then it's just a matter of cutting, folding, squeezing together with pliers, and screwing.
And one screw should be enough if you fold it twice:
[image]

Will think about it! Thanks to both

 

[Jante]

Hope to avoid that! It becomes time-consuming to fit everything. This solves the whole problem.

Nah, not so time-consuming, I have quite a bit of netting in the garden and I have placed the netting on the posts, drawn a marking for each wire, drilled and threaded it with the post slightly angled at the start. Finished by nailing it with staples to hold it all together. Cut the netting so there is a projection of 2-3 cm that should go into the post and in the cat house, there is a frame on all 4 sides of the netting.
Image from the cat house:


//Jante